Fiók Kapcsolat
Kosár
DPD & FedEx – a várható kiszállítás dátuma a termékoldalon.
Segítségre van szüksége? Kérdezze AI-asszisztensünket!

Flashforge AD5X IFS átviteli panel tartozék 3D nyomtatóhoz (MPN 20004784001)

Flashforge AD5X IFS átviteli panel tartozék 3D nyomtatóhoz (MPN 20004784001)
Flashforge AD5X IFS átviteli panel tartozék 3D nyomtatóhoz (MPN 20004784001)
8 540 Ft
PDF
PDF

Szállítás és visszaküldés

Várható kiszállítás december 8., kedd
Részletes csomagkövető rendszerünk segítségével folyamatosan tájékoztatjuk
Fizetési lehetőségek
BankkártyaVisaMastercardPayPalApple PayGoogle PayBanki átutalás

Leírás

The Transfer board Flashforge AD5X IFS is an internal accessory designed for compatible Flashforge 3D printers. It functions as a transfer/interface board to enable connectivity and communication between printer modules, helping to restore or maintain signal paths between the main control board and peripheral components. The part is intended for use when a printer exhibits communication errors, intermittent behavior, or during routine repair and maintenance that requires replacement of an aging or damaged interface board.

Advantages

This transfer board provides direct electrical connections and standardized interface points that simplify swapping defective components, reducing diagnostic time during service. It is engineered to match the electrical and mechanical characteristics required by Flashforge AD5X-class systems, ensuring reliable signal transmission and stable performance when properly installed. The board supports routine repair workflows and can be used to return a printer to factory communication functionality without replacing larger assemblies.

Suitable for

  • Replacing a faulty interface board in compatible Flashforge 3D printers
  • Repairing printers with intermittent communication or signal errors
  • Servicing and maintenance tasks that require restoring internal connections

Key specifications

  • Function: transfer/interface board for internal connectivity
  • Compatibility: designed for use with compatible Flashforge 3D printer models in the AD5X series
  • Form factor: compact PCB sized for internal mounting in printer chassis
  • Connectors: standard board-to-board and cable connector interfaces for peripheral modules
  • Use environment: intended for indoor use within closed 3D printer enclosures

How to use

Install the transfer board by powering down and unplugging the printer, opening the printer chassis to access the internal electronics, and removing any obstructing components. Disconnect cables from the defective board, note connector positions or photograph them for reference, then remove mounting screws and replace the old board with the Flashforge AD5X IFS transfer board. Reconnect cables to the corresponding connectors, secure the board with mounting screws, reassemble the chassis, and restore power. After installation, perform a basic communication and function check following the printer manufacturer’s service procedures.

Recommendations

Work in a static-free environment and use ESD protection when handling the board. Verify compatibility with the specific Flashforge model before installation, and follow manufacturer service instructions for safe disassembly and reassembly. If unsure about the replacement procedure, consult a qualified technician to avoid damage to other components.

Főbb jellemzők
  • Replacing a faulty interface board in compatible Flashforge 3D printers
  • Repairing printers with intermittent communication or signal errors
  • Servicing and maintenance tasks that require restoring internal connections
  • Function: transfer/interface board for internal connectivity
  • Compatibility: designed for use with compatible Flashforge 3D printer models in the AD5X series
  • Form factor: compact PCB sized for internal mounting in printer chassis
  • Connectors: standard board-to-board and cable connector interfaces for peripheral modules
  • Use environment: intended for indoor use within closed 3D printer enclosures

Műszaki adatok

Műszaki adatok
Eszközkompatibilitás
Flashforge AD5X
Terméktípus
3D nyomtató kiegészítő
Az elmúlt 6 hónap ártörténete
Flashforge AD5X IFS átviteli panel tartozék 3D nyomtatóhoz (MPN 20004784001)
Jelenlegi
8 540 Ft
Legalacsonyabb 7 nap
8 309 Ft
Legmagasabb 7 nap
8 540 Ft
24 órás változás
+64 Ft   +1%
7 napos változás
+147 Ft   +2%
30 napos változás
0 Ft   0%

Értékelés írása

Értékelés *
Megjegyzés: A HTML-formázás nem jelenik meg!

Azonos sorozat és alternatívák

12

Népszerű termékek ebben a kategóriában

8
Eladó: UAB KUR LT · Gariūnų g. 57-14, LT-02300 Vilnius, Litvánia · Cégjegyzékszám 303192950 · Közösségi adószám LT100008198612 · Szállítás az EU-ból (Litvánia)
WhatsApp
Messenger
Üdvözlöm, a DistriNode AI-asszisztense vagyok. Szívesen segítek termékek keresésében, a lehetőségek összehasonlításában, PDF-árajánlatok készítésében vagy ügyfélszolgálati bejelentések indításában.
Összes kategória