Fiók Kapcsolat
Kosár
DPD & FedEx – a várható kiszállítás dátuma a termékoldalon.
Segítségre van szüksége? Kérdezze AI-asszisztensünket!

Alaplap (AD5X IFS) Flashforge 3D nyomtatóhoz — cserepanel, MPN 20004780001

Alaplap (AD5X IFS) Flashforge 3D nyomtatóhoz — cserepanel, MPN 20004780001
Alaplap (AD5X IFS) Flashforge 3D nyomtatóhoz — cserepanel, MPN 20004780001
9 005 Ft
PDF
PDF

Szállítás és visszaküldés

Várható kiszállítás december 10., csütörtök
Részletes csomagkövető rendszerünk segítségével folyamatosan tájékoztatjuk
Fizetési lehetőségek
BankkártyaVisaMastercardPayPalApple PayGoogle PayBanki átutalás

Leírás

The Main Board (AD5X IFS) for Flashforge 3D Printer is a replacement control PCB designed to manage the printer's core electronics. It integrates signal routing for stepper motors, endstops and sensors, heater and fan control, and communication interfaces between the printer's firmware and hardware. Intended as a direct replacement for a defective main board, this unit restores control of motion, temperature regulation and peripheral devices to recover printing capability.

Advantages

This replacement main board provides the same functional layout and connections as the original Flashforge control board, enabling straightforward swap-in installation. It supports coordinated control of motors and heaters, accurate sensor inputs for temperature and position, and stable power distribution to maintain reliable printing operations. Using a compatible board reduces downtime and avoids the need for full printer replacement.

Suitable for

  • Repairing a Flashforge 3D printer with a faulty or damaged main control board
  • Restoring lost functionality after electrical failure or component damage
  • Replacing a burnt or non-responsive PCB to resume normal printing

Key specifications

  • Function: central control PCB for 3D printer electronics
  • Controls: stepper motor drivers, endstop and sensor inputs, heater and fan outputs
  • Interfaces: standard board connectors for thermistors, heaters, fans, motors and control panel
  • Power handling: designed for typical desktop FDM printer voltages and loads
  • Form factor: replacement board sized to fit the corresponding Flashforge chassis and mounting points
  • Compatibility: intended for direct replacement in compatible Flashforge models

How to use

Power down the printer and disconnect it from mains supply before beginning any replacement. Remove the printer cover to access the controller area, note or photograph existing cable routing and connector positions, then disconnect cables from the old main board. Unscrew and remove the faulty PCB, install the replacement board aligning mounting holes and connectors, and reconnect all wiring according to the recorded layout. Reassemble the enclosure, reconnect power, and perform initial power-on checks. Verify thermistor readings, heater activation, endstop recognition and motor movement through the printer's control interface before starting a print.

Recommendations

Use only the specified board layout and connector types to avoid mismatches. Inspect cables and connectors for damage and replace any worn wiring. After installation, calibrate axis endstops and temperature settings, and run a test print to confirm stable operation. If unsure about wiring or firmware compatibility, consult the printer service manual or seek professional technical support.

Főbb jellemzők
  • Repairing a Flashforge 3D printer with a faulty or damaged main control board
  • Restoring lost functionality after electrical failure or component damage
  • Replacing a burnt or non-responsive PCB to resume normal printing
  • Function: central control PCB for 3D printer electronics
  • Controls: stepper motor drivers, endstop and sensor inputs, heater and fan outputs
  • Interfaces: standard board connectors for thermistors, heaters, fans, motors and control panel
  • Power handling: designed for typical desktop FDM printer voltages and loads
  • Form factor: replacement board sized to fit the corresponding Flashforge chassis and mounting points
  • Compatibility: intended for direct replacement in compatible Flashforge models
Az elmúlt 6 hónap ártörténete
Alaplap (AD5X IFS) Flashforge 3D nyomtatóhoz — cserepanel, MPN 20004780001
Jelenlegi
9 005 Ft
Legalacsonyabb 7 nap
8 770 Ft
Legmagasabb 7 nap
9 005 Ft
24 órás változás
+137 Ft   +2%
7 napos változás
—   
30 napos változás
—   

Értékelés írása

Értékelés *
Megjegyzés: A HTML-formázás nem jelenik meg!

Azonos sorozat és alternatívák

12

Népszerű termékek ebben a kategóriában

8
Eladó: UAB KUR LT · Gariūnų g. 57-14, LT-02300 Vilnius, Litvánia · Cégjegyzékszám 303192950 · Közösségi adószám LT100008198612 · Szállítás az EU-ból (Litvánia)
WhatsApp
Messenger
Üdvözlöm, a DistriNode AI-asszisztense vagyok. Szívesen segítek termékek keresésében, a lehetőségek összehasonlításában, PDF-árajánlatok készítésében vagy ügyfélszolgálati bejelentések indításában.
Összes kategória